Ventiflex PLUS Modular Fitting System

The modular system of ventilation fittings is a versatile set of plastic elements, which can be used to assemble any type of plenum box or distribution box (manifold) in a “minute”. The connections between the fittings are airtight and connection spigots fit perfectly into the ventilation ducts.

The VENTIFLEX PLUS air distribution system has a 30-year warranty on the biocidal coating. Each element of the system contains a protective coating based on microsilver particles, which protects against the multiplication of fungi and bacteria. The reliability of the coating has been confirmed by Polish accredited laboratories.



Installation instruction for the modular system

Plenum box

It is the basic component of the system used as the base to which diffusers are connected with or without the use of the extension. The box can be provided with 2 or 1 spigot (the set includes an additional end cap).

Material: ABS with the addition of microsilver particles

Self assembly set.

see the video

Dimensions:

Symbol W [mm] L [mm] h [mm] H [mm] M [kg] Rebate group
MSR-1-2xDN75-DN125 231 270 92 113 0,43 GR1
6 spigot distribution box

5 or 6 spigot distribution box with round connector DN160. It is designed to install both at the air intake and outlet side. The box is equipped with an end cap to plug one unused spigot DN75.

Material: ABS with the addition of microsilver particles.

Self assembly set.

Dimensions
*Height of the distribution box with/without the connection spigot

 

Symbol W [mm] L [mm] H [mm] M [kg] Rebate group
MRO-6xDN75/DN160 333 359 131 (88)* 1,21 GR1
8-spigot distribution box

7 or 8 spigot distribution box with round connector DN200. It is designed to install both at the air intake and outlet side. The box is equipped with an end cap to plug one unused spigot DN75.

Material: ABS with the addition of microsilver particles.

Self assembly set.

Dimensions
*Height of the distribution box with/without the connection spigot

 

Symbol W [mm] L [mm] H [mm] M [kg] Rebate group
MRO-8xDN75/DN200 359 387 131 (88)* 1,28 GR1
10 spigot distribution box

9 or 10 spigot distribution box with round connector DN200. It is designed to install both at the air intake and outlet side. The box is equipped with an end cap to plug one unused spigot DN75.

Material: ABS with the addition of microsilver particles.

Self assembly set.

see the video

Dimensions
*Height of the distribution box with/without the connection spigot

 

Symbol W [mm] L [mm] H [mm] M [kg] Rebate group
MRO-10xDN75/DN200 359 500 131 (88)* 1,73 GR1
12 spigot distribution box

11 or 12 spigot distribution box with round connector DN200. It is designed to install both at the air intake and outlet side. The box is equipped with an end cap to plug one unused spigot DN75.

Material: ABS with the addition of microsilver particles.

Self assembly set.

Dimensions
*Height of the distribution box with/without the connection spigot

Symbol W [mm] L [mm] H [mm] M [kg] Rebate group
MRO-12xDN75/DN200 359 614 131 (88)* 2,20 GR1
Base module

The basic element of the system is the base which can be used to construct plenum boxes and distribution boxes.
Material: ABS with the addition of microsilver particles

Dimensions:

Symbol W [mm] L [mm] H [mm] M [kg] Rebate group
MBVT+75 276 250 88 0,47 GR1
Basic module pass-through

The system element that allows to create a pass-through manifolds. Building this type of manifolds makes it possible to reduce the numer of holes in the ceiling for ventilation shafts.

Material: ABS with the addition of microsilver particles.

Dimensions:

Symbol W [mm] L [mm] H [mm] M [kg] Rebate group
MBPVT+75 276 250 88 0,30 GR1
Segment module

A part that allows the plenum boxes and distribution boxes to be extended with an additional row of connecting holes. One segment module extends the box by 120 mm.

Material: ABS with the addition of microsilver particles

Dimensions

Symbol W [mm] L [mm] H [mm] M [kg] Rebate group
MSVT+75 140 250 88 0,36 GR1
Inter-module connector

The inter-module connector allows two base modules to be connected together. This fitting enables you to assemble a pass-through distribution box that is e.g. used to move the ventilation riser in the desired direction. One inter-module connector extends the box by 25 mm.

Material: ABS with the addition of microsilver particles

Dimensions

Symbol W [mm] L [mm] H [mm] M [kg] Rebate group
LMVT+75 80 255 83 0,24 GR1
Cover with holes

The cover with holes is used to close the module sides and to allow additional spigots DN75 to be connected.

Material: ABS with the addition of microsilver particles

Dimensions

Symbol L [mm] H [mm] M [kg] Rebate group
DOVT+75 248 78 0,09 GR1
Cover without holes

The cover without holes is used to close the sides of the base and segment modules.

Material: ABS with the addition of microsilver particles

Dimensions

Symbol L [mm] H [mm] M [kg] Rebate group
DOVT+75 248 78 0,12 GR1
Spigot extension DN125

The spigot extension allows one to install the system termination components e.g. air supply diffusers at the desired distance from the plenum box. It is used for ceiling penetrations or installation of the system in the suspended ceiling space.

Material: PCV

Dimensions

Symbol L [mm] D [mm] M [kg] Rebate group
PO-DN125x300 300 125 0,25 GR1
PO-DN125x1500 1500 125 1,25 GR1
Spigot DN75

The spigot allows one to connect the VENTIFLEX VTX air duct to the distribution box or plenum box hole. It is screwed in through the bayonet connector and it tightly adheres to the surface of the modules in which it is mounted.

Material: ABS with the addition of microsilver particles

Dimensions

Symbol D [mm] L [mm] M [kg] Rebate group
KRVT+75 84 53 0,05 GR1
End cap DN75

The end cap is a part that is used to close unused holes of the spigots DN75.
It is mounted with the bayonet connector and thus it tightly adheres to the surface of the module.

Material: ABS with the addition of microsilver particles

Dimensions

Symbol M [kg] Rebate group
ZAVT+75 0,02 GR1
Spigots DN125, DN125M, DN160, DN200

The spigots are mounted on the base module. These components allow one to connect the distribution box to the ventilation riser or the plenum box to the diffuser.

Material: ABS with the addition of microsilver particles

Dimensions

Symbol Typ D/d [mm] H [mm] M [kg] Rebate group
KR-125 Nypel 230/125 43 0,19 GR1
KR-125 Mufa Mufa 230/127 20 0,14 GR1
KR-160 Nypel 230/160 43 0,19 GR1
KR-200 Nypel 230/200 43 0,18 GR1
External connector

The connector allows one to connect the VENTIFLEX VTX ventilation ducts together.
The joint tightness is ensured by the UVX-DN75 seal.

Material: polyethylene

Dimensions

Symbol D [mm] L [mm] M [kg] Rebate group
ZV-90 93 143 0,10
ZV-75 79 115 0,05 GR1
Seal

The seal is placed on the VENTIFLEX VTX ventilation ducts in order to ensure proper tightness of the connection with the spigots and the external connector. It is recommended to use two seals. This seal also fits on the VTX-DN90 duct.

Material: EPDM

Dimensions

Symbol D [mm] d [mm] M [kg] Rebate group
UVX-DN75 78 62 50 pcs 0,17 GR1
Spigot plugs

The plug is used to protect the air distribution system against dirt during construction works. It is mounted on e.g. the spigot extensions.

Material: polyethylene

Dimensions

Symbol D [mm] L [mm] M [kg] Rebate group
ZA-DN125 125 25 5 pcs 0,2 GR2
ZA-DN75 75 20 50 pcs 0,35 GR2
ZA-DN200 200 40 5 pcs 0,4 GR2
ZA-DN160 160 40 5 pcs 0,3 GR2
Adapter from MSVT+75 to spigot DN160 or DN200

This adapter is used to create the distribution box with a side supply with round section DN160 or DN200.
The set includes the steel adapter and segment module.

Material: galvanised steel + ABS with the addition of microsilver particles

Dimensions

Symbol D [mm] L [mm] H [mm] Rebate group
RED-DN200/MS-VT+75 200 250 88 GR1
RED-DN160/MS-VT+75 160 250 88 GR1
Adapter from MSVT+75 to 200x50 flat duct

This adapter is used to create the distribution box with a side supply with 200x50mm rectangular section.
The set includes the steel adapter and segment module.

Material: galvanised steel + ABS with the addition of microsilver particles

Dimensions

Symbol l [mm] h [mm] L [mm] H [mm] Rebate group
RED-200×50/MS-VT+75 200 50 250 88 GR1
Mounting spanner

The mounting spanner is used to tighten the spigots: KRVT+75, KR-125, KR-125M, KR-160, KR-200 and end caps ZAVT+75 to the module bodies. It is made of powder-coated steel.